Installation Instructions
JS2k.com Windscreens
IMPORTANT: You CANNOT have the Secret Compartment open when you are moving the soft top with the Tall JS2k.com Windscreen.
Pictures to come soon, as this install is a bit tricky.
1. Put the top down.
2. Use a flathead screwdriver to pry the 'nubs' on each side of the windscreen to expose the screws.
3. Remove the two screws under the 'nubs.'
4. Use a credit card, paint scraper, or a plastic pry tool and start prying the sides of the black part of the windscreen. This may take some time, patience, and elbow grease. Be careful not to allow your tool to slip and gouge yourself or the windscreen. I used a paint scraper, and it took 15 minutes the first time to separate the housing.
5. Once the housing has been separated, remove the three screws holding the windscreen.
6. Replace the old windscreen with the JS2k.com Windscreen.
7. Screw the three screws into the windscreen to secure it.
8. Use a bit of clear silicone adhesive on the two edges of the black housing. We recommend clear silicone because it's clear and it is easy to remove if you wish to go back to stock.
9. Apply a piece of tape to both sides of the housing to hold it together for at least 12 hours so the clear silicone will dry.
10. Remove the tape after 12 hours.
11. Reinstall windscreen, and screws, and nubs.
Notes: You can open the secret compartment without folding the Tall Windscreen down when the top is up. With the Tall Windscreen, top operation is not affected.
LED Conversions
Dome Lights
1. Use a flathead screwdriver to pry open the dome light. You should be able to feel with your finger that there is a slot to place the screwdriver.
2. Remove existing bulb. Caution: The bulb may be hot!
3. Insert new LED bulb.
4. Turn dome lights on
5. If LED bulb does not illuminate, remove the LED bulb, turn it around, and reinsert it.
6. Replace dome light cover
Trunk Lights
1. Use a flathead screwdriver to pry open the trunk light. The hinge pivots on the left side, so pry from the right side.
2. Remove existing bulb. Caution: The bulb may be hot!
3. Insert new LED bulb.
4. If bulb does not illuminate, remove LED bulb, turn it around, and reinsert it.
5. Close cover
License Plate light
1. Coming soon, need to confirm steps on my own car.
Oil Drain Valves
Steps for installation:
1. Remove OEM drain plug
2. Let oil drain
3. Thread the valve to the adapter by hand as tight as possible.
4. Use and adjustable wrench to turn it not more than a quarter of a turn more
5. Thread the adapter and valve into the oil pan by hand as tight as possible
6. Again, use the adjustable wrench to turn it just a bit more. Probably not even a quarter of a turn.
Steps for an oil change after Oil Drain Valve has been installed
1. Open hood
2. Place oil drain pan under oil pan
3. Unscrew oil filter
4. Open the Oil Drain Valve
5. Screw in new filter
6. Close the Oil Drain Valve
7. Add oil
Keyhole Covers
Simply, push the keyhole cover into the keyhole. After fully inserted, you can turn it slightly to the left or right to ensure it will stay in.
To remove the keyhole cover, insert a business card underneath the keyhole cover and pry it out.
If your keyhole cover does not stay inside the keyhole or if the paint ever chips, please contact me and I will ship you a replacement.
IMPORTANT: You CANNOT have the Secret Compartment open when you are moving the soft top with the Tall JS2k.com Windscreen.
Pictures to come soon, as this install is a bit tricky.
1. Put the top down.
2. Use a flathead screwdriver to pry the 'nubs' on each side of the windscreen to expose the screws.
3. Remove the two screws under the 'nubs.'
4. Use a credit card, paint scraper, or a plastic pry tool and start prying the sides of the black part of the windscreen. This may take some time, patience, and elbow grease. Be careful not to allow your tool to slip and gouge yourself or the windscreen. I used a paint scraper, and it took 15 minutes the first time to separate the housing.
5. Once the housing has been separated, remove the three screws holding the windscreen.
6. Replace the old windscreen with the JS2k.com Windscreen.
7. Screw the three screws into the windscreen to secure it.
8. Use a bit of clear silicone adhesive on the two edges of the black housing. We recommend clear silicone because it's clear and it is easy to remove if you wish to go back to stock.
9. Apply a piece of tape to both sides of the housing to hold it together for at least 12 hours so the clear silicone will dry.
10. Remove the tape after 12 hours.
11. Reinstall windscreen, and screws, and nubs.
Notes: You can open the secret compartment without folding the Tall Windscreen down when the top is up. With the Tall Windscreen, top operation is not affected.
LED Conversions
Dome Lights
1. Use a flathead screwdriver to pry open the dome light. You should be able to feel with your finger that there is a slot to place the screwdriver.
2. Remove existing bulb. Caution: The bulb may be hot!
3. Insert new LED bulb.
4. Turn dome lights on
5. If LED bulb does not illuminate, remove the LED bulb, turn it around, and reinsert it.
6. Replace dome light cover
Trunk Lights
1. Use a flathead screwdriver to pry open the trunk light. The hinge pivots on the left side, so pry from the right side.
2. Remove existing bulb. Caution: The bulb may be hot!
3. Insert new LED bulb.
4. If bulb does not illuminate, remove LED bulb, turn it around, and reinsert it.
5. Close cover
License Plate light
1. Coming soon, need to confirm steps on my own car.
Oil Drain Valves
Steps for installation:
1. Remove OEM drain plug
2. Let oil drain
3. Thread the valve to the adapter by hand as tight as possible.
4. Use and adjustable wrench to turn it not more than a quarter of a turn more
5. Thread the adapter and valve into the oil pan by hand as tight as possible
6. Again, use the adjustable wrench to turn it just a bit more. Probably not even a quarter of a turn.
Steps for an oil change after Oil Drain Valve has been installed
1. Open hood
2. Place oil drain pan under oil pan
3. Unscrew oil filter
4. Open the Oil Drain Valve
5. Screw in new filter
6. Close the Oil Drain Valve
7. Add oil
Keyhole Covers
Simply, push the keyhole cover into the keyhole. After fully inserted, you can turn it slightly to the left or right to ensure it will stay in.
To remove the keyhole cover, insert a business card underneath the keyhole cover and pry it out.
If your keyhole cover does not stay inside the keyhole or if the paint ever chips, please contact me and I will ship you a replacement.
Paypal Verified!
Shop Securely!
Copyright © 2010 JS2k.com. Powered by Zen Cart. All rights reserved.